Sterling Silver Crescent and Bead Earrings
MATERIALS Desired
3" 4 x 1 mm sterling silver rectangle wire
Twenty-just one 'Λ* head pins
Two turquoise disc beads
A person Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What suggestions would you give a commencing artist?
“Do what you adore. Investigate diverse media. Offer with a selective, limited, basis in the beginning to view what will work or what would not work for you before you leap into A significant outlay of money and effort.*
-Sally J. Phillips Jewellery Designer
Instruments Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Hard, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Wonderful grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Spherical nose pliers
one.Make use of the ruler to evaluate and mark two one Vi’ parts of four x one mm rectangle sterling silver wire.
2Using a jeweler's observed or tin snips, Slash the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File each end from the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If wanted, You need to use the file to round the finishes on the rectangle wire items. Make use of a wonderful grit sanding pad to go in excess of the world in which you have submitted to clean the perimeters and take away any file marks.
four.Make use of the ruler to evaluate and mark /*." from one particular conclude on the one Vi’ items of rectangle wire and spot a mark in the center in the wire. This is where you are going to drill the holes to slide the head pins via.
5.Put on your own basic safety Eyeglasses!!! Area the 1 Vi" rectangle wire items onto a hard, flat surface. Location the point of the awl on the mark that you made Vm,' from one end of your rectangle wire parts, and firmly strike the moment on the highest with the awl by using a hammer. This will make a pilot hole for drilling holes into your rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter five
six.Utilizing a /is" drill bit. drill holes into a single stop from the rectangle wire pieces with a handheld rotary Software, flex shaft, or drill push (when even now donning your security glasses!).
7.Utilize the file or high-quality grit mens ring sanding pad to remove any burs or rough edges left from drilling holes into the Mens Ring rectangle wire parts.
eight.Curve equally 1W items of rectangle wire into a “C" shape employing a mens ring ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, Mens Ring use two pair of chain nose pliers. Holding a person set of pliers in Every single hand, grasp Each and every finish of the one Vi* rectangle wire piece Together with the pliers and gently bend the rectangle wire into a “C* condition. Assess the two from the C-formed rectangle wire parts and alter the curves so that they are similar in si2e. Established these apart.
9.Utilize the ruler to evaluate and mark the rubber tube into four equal parts measuring Vm’ Every single. Use scissors to cut the rubber tube.
10.Put the turquoise disc bead on to The top pin and add a person V·' bit of the rubber tube, spot the head pin in the gap within the C-formed rectangle wire, and afterwards incorporate the other V«" bit of rubber tube.
thirteen. Hold The pinnacle pin Along with the bead, rubber tube, as well as the rectangle wire on it in one hand Along with the wire that you just bent pointing toward you. Utilizing the round nose pliers, grip the end of The pinnacle pin wire that is certainly pointing toward you and roll it clear of you (think about turning the ignition important to get started on your vehicle). Release the pliers from The pinnacle pin wire.
At this time, the opening in the loop at the best of The top pin wire should however be massive enough to slide the ear wire on. Once you add the ear wire, make use of the round nose pliers to grasp the loop of The pinnacle pin wire and roll it closed. You can use the spherical nose or chain nose pliers to adjust The form in the loop at the top of The top pin if you have to.
eleven. Make use of the ruler to evaluate and mark /(.’ earlier mentioned the top bit of the hollow rubber tube. With all the wire cutters or tin snips, cut The top pin wire Yu.’ above the best Mens Ring in the hollow rubber tube.
twelve. Make use of the chain nose pliers to bend the head pin wire close to the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat these measures for the 2nd earring.